How to install a zipper in a pillow with piping.

There are quite a few tutorials out there on how to install a zipper in a piped pillow.  Trust me, I've tried most all of them.  And after many trial and error approaches (mostly error) using these methods, I've come up with a hybrid way of using bits and pieces from some of these and incorporating them with my own ideas.  I thought I'd share my way with you.

If this way doesn't work for you, keep looking and trying until you do.  It's really about patience and practice.  I'll even give you my tried and true way of matching patterns.

I'm assuming you know how to sew a basic pillow with a zipper.  There are plenty of tutorials out there if not.  I'm only going to show you the basics for installing a zip when there is piping involved.

The first thing to do is press one side of the invisible zipper flat. At this point, you should already have your piping attached to the pillow front or back.

I like using a piping or welting foot on my machine.  They aren't terribly expensive and well worth their weight in gold if you do a lot of piping.  I have already serged the edges of each pillow section where the zipper will go.

Then I measure in 2-3" from each edge (depending on the pillow size) and mark my zipper placement.  This is where I will start and stop stitching.  This is done on both pillow pieces.

Next, line up the piping under your piping foot just like you did when you attached it.  Take the flat zipper (the side you pressed flat) and put that under your piping foot and on top of your pillow edge right side down.  The zipper teeth should be right on the edge of the piping and inside the groove of the piping foot.  See where my skewer is pointing?  My needle position is centered.  I don't touch it.

I use a skewer to gently keep the zipper in place as I stitch pressing slightly in that groove of the piping.

This is what it will look like when you have that side complete.

Now the zipper is closed and marks are placed where you stopped and started stitching on the first side.  I should have gotten a close up here.  If you'll look where the #38 is on my cutting mat, you can just make out my red mark.

In order to line up the stripes, marks will also be placed on the other side of the zipper at each stripe. There are two red marks side by side in this picture.  One is my stripe mark, and the other is where the stitching started.

Place the other pillow piece on top right sides facing.

I love wonder tape!  It's one staple I will never be without in my sewing room.  It makes these projects so easy.  It's my secret weapon.

Place a piece of wonder tape on the pillow piece from one mark to the other (these are marks for the zipper placement).  This is one side.

Yellow arrow is where the wonder tape is placed.  The fabric is folded back on itself.  Peel off the paper backing on the wonder tape.

Unzip the zipper and lay it on top of the wonder tape matching the start/stop marks and the stripe line marks.  No pinning and no shifting.  That zipper will stay put.  Stitch that puppy on!  I switch to my invisible zipper foot for this step.  You could always press this side flat and use a regular zipper foot.

And it should look like this. Look at those perfectly aligned stripes!!  Sorry for my messy work area. I was making 6 of these when I did the tute!

The other secret here is to stitch the opposite side next, then stitch the sides.  Get out your wonder tape and put it on the side without piping.  And place the two right sides together.  If you are brave, just put the two sides together and pin at each stripe checking both front and back to make sure the pin hits the stripe on each at the stitch line.  I recommend using the wonder tape until you've done a few.  Just be sure to match your stripes whatever method you choose.  I do it this way so if I have a mistake or my stripe placement is off, it's easier to rip out.

If using pins, you should have one at every stripe.  Stitch.

Now you have a big pillow tube!

Now simply stitch the two sides (remember to open the zipper) and that's it!  Marvel at your newly stitched, perfectly aligned striped, piped pillow.  Say that fast 3 times!!

I hope this method works for you.  Please feel free to ask questions if I haven't made something clear.

Thanks for stopping by!
Angela

Children's Corner Mary De

I have been busy in my workroom and have had very little time to post.  I think I'm nearly caught up now, so I thought I'd show you a few things I've accomplished over the last few weeks.

This is a Children's Corner Mary De.  This pattern is one of my favorites.

I loved this print fabric but didn't have enough for the entire dress, so I added a black band along the bottom and trimmed it with ric rac.  I also used a smocked insert.

The smocking plate is from Ellen McCarn -  It's called Ladybug Family

This is the first time I've smocked into the arm holes on the Mary De.  It was a bear.  All the bulk made it impossible to turn that seam allowance to the inside.  So I chose to put a bias binding around those edges instead.  I like it. Just remember to cut away the seam allowance if you do this.  This is also the first time I've done double piping.

This has to be the best collar I've ever done.  I used Gail Doane's method of adding the piping and cutting it out.  I've never done it before and it took me two tries, but I love it!  I'll always use this method.

I had these sweet little ladybug buttons for the back closure.

I added little ladybug buttons to the sleeves.

And of course she had to have matching socks.  Laurie at Southern Stitches has a great tutorial for these.